Service Manual Parts Town-Books Download

SERVICE MANUAL Parts Town
22 Feb 2020 | 21 views | 0 downloads | 60 Pages | 1.82 MB

Share Pdf : Service Manual Parts Town

Download and Preview : Service Manual Parts Town


Report CopyRight/DMCA Form For : Service Manual Parts Town



Transcription

Table of Contents,Section 1 Introduction 1,Model 358 Specifications 4. Model 359 Specifications 5,Running Specifications 6. General Installation Instructions 7,Refrigerant 9,Environmental Notices 10. Section 2 Controls Systems 11,Thermistor Control 12. Thermistor Curve 14,Refrigeration System 15,Maintaining Quality 16.
Section 3 Troubleshooting 17,Troubleshooting Thermistor Components 18. General Troubleshooting Guide 19,Overrun 22,Section 4 General Service 23. Evaporator Oil 24,Rear Bearing Unit Alignment 25,Pulley Alignment 26. Rear Shell Bearing 26,Beater Shaft Removal 26,Preventative Maintenance 27. Models 358 359 Table of Contents,Table of Contents Page 2.
Section 5 Parts 29,Parts Warranty Explanation 30,Model 358 Operator Parts 31. Model 358 Exploded View 32,Model 358 Shell Assembly 34. Model 358 Control A X66731 33 35,Model 358 Channel A Control X63534 36. Models 358 359 Beater Door Assembly 38,Model 359 Operator Parts 39. Model 359 Exploded View 40,Model 359 Shell Assembly 42.
Model 359 Channel A Control X65222 43,Model 359 Control A X65279 33 44. Models 358 359 Switch A Draw X65212 SER 45,Models 358 359 Accessories 46. Parts List 47,Wiring Diagrams 54, CAUTION Information in this manual is intended to be used by Taylor Authorized. Service Technicians only, Note Continuing research results in steady improvements therefore information. in this manual is subject to change without notice. E August 2010 Taylor Original Publication,Updated March 2011.
All rights reserved,The word Taylor and the Crown design. Taylor Company, are registered trademarks in the United States 750 N Blackhawk Blvd. of America and certain other countries Rockton IL 61072. Table of Contents Models 358 359,Section 1 Introduction. S Specifications,S Running Specifications,S General Installation Instructions. S Refrigerant,S Environmental Notices,Models 358 359 1 Introduction.
protect against the leakage of current and, Safety be installed by authorized personnel to the. local codes,S Supply cords used with this unit shall be. We at Taylor Company are deeply committed to oil resistant sheathed flexible cable not. manufacturing safe operating and serviceable lighter than ordinary polychloroprene or. equipment The many built in safety features that other equivalent synthetic. are part of all Taylor equipment are aimed at elastomer sheathed cord Code designation. protecting operators and trained service technicians 60245 IEC 57 installed with the proper cord. alike anchorage to relieve conductors from strain,including twisting at the terminals and. protect the insulation of the conductors from,This manual is intended exclusively for abrasion. Taylor Company authorized service personnel, Failure to follow these instructions may result in.
electrocution or damage to the unit,DO NOT attempt to run the equipment. unless you have been properly trained to do so,Failure to follow this instruction may result in. equipment damage poor equipment performance This unit is provided with an equipotential. health hazards or personal injury grounding lug that is to be properly attached to. either the rear of the frame or the under side of the. base pan near the entry hole for incoming power by. the authorized installer The installation location is. CAUTION THIS EQUIPMENT MUST BE marked by the equipotential bonding symbol 5021. PROPERLY GROUNDED Do not operate this unit of IEC 60417 1 on both the removable panel and. unless it is properly grounded and all service panels the equipment s frame as well as on the diagram. and access doors are restrained with screws Failure. to do so can result in severe personal injury from. electrical shock,DO NOT remove the freezer door or any. internal operating parts examples beater scraper,blades etc unless all control switches are in the. OFF position Failure to follow these instructions,S DO NOT attempt any repairs unless the.
may result in severe personal injury from hazardous. main power supply to the unit has been moving parts. disconnected,S DO NOT operate the unit with larger fuses. than specified on the data label,S Stationary appliances which are not. equipped with a power cord and a plug or THIS UNIT HAS MANY SHARP EDGES. other device to disconnect the appliance THAT CAN CAUSE SEVERE INJURIES. from the power source must have an all pole,disconnecting device with a contact gap of. at least 3 mm installed in the external,installation. This unit must be installed on a level, S Appliances that are permanently connected surface to avoid the hazard of tipping Extreme care.
to fixed wiring and for which leakage should be taken in moving this equipment for any. currents may exceed 10 mA particularly reason, when disconnected not used for long Two or more people are required to safely move this. periods or during initial installation shall unit Failure to comply may result in personal injury. have protective devices such as a GFI to or equipment damage. Introduction 2 Models 358 359, This unit must NOT be installed in an area Cleaning and sanitizing schedules are. where a water jet or hose can be used NEVER use governed by your state or local regulatory agencies. a water jet or hose to rinse or clean this unit Using a and must be followed accordingly Please refer to. water jet or hose on or around this equipment may the cleaning section of the Operator Manual for the. result in the electrocution of the user or damage to proper procedure to clean this unit. the equipment,Models 358 359 3 Introduction,Model 358 Specifications. S Freezing Cylinder One 7 quart 6 6 liter S Air Cooled Clearance 3 76 mm around. capacity all sides,S Mix Hopper One 20 quart 18 9 liter. capacity Refrigerated and insulated S Dimensions,Width 16 406 mm.
S Beater Motor One 1 5 hp Depth 30 762 mm,Height 55 7 8 1418 mm. S Refrigeration Unit One approximately,Floor Clearance 3 1 2 89 mm mounted. 9 500 btu hr compressor Refrigerant 404A,on standard casters. S Electrical Standard is 208 230 60 3, however other electrical characteristics are S Approximate Weights. available Each unit requires electrical Net 356 lbs 161 5 kgs. service Crated 400 lbs 181 4 kgs, Three Phase Maximum Fuse Size 20A Volume 22 3 cu ft 63 cu m.
Minimum Circuit Ampacity 16A, For exact electrical information always refer Availability and specifications subject to change. to the data label of the unit without notice,Introduction 4 Models 358 359. Model 359 Specifications, S Freezing Cylinder Two 7 quart 6 6 liter S Air Cooled Clearance 3 76 mm around. capacity all sides,S Mix Hopper Two 20 quart 18 9 liter. capacity Refrigerated and insulated S Dimensions,Width 26 660 mm.
S Beater Motor Two 1 5 hp Depth 32 3 8 822 mm,Height 55 7 8 1418 mm. S Refrigeration Unit Two approximately,Floor Clearance 4 1 4 108 mm mounted. 9 500 btu hr compressors Refrigerant 404A,on standard casters. S Electrical Standard is 208 230 60 3, however other electrical characteristics are S Approximate Weights. available Net 580 lbs 263 1 kgs, Each unit requires electrical service Crated 673 lbs 305 3 kgs.
Maximum Fuse Size 35A Volume 41 1 cu ft 1 16 cu m,Minimum Circuit Ampacity 30A. For exact electrical information always refer Availability and specifications subject to change. to the data label of the unit without notice,Models 358 359 5 Introduction. Running Specifications, Expansion Valve Setting Water Cooled The high side pressure for water. 404A HP62 20 22 PSI 138 152 kPa cooled units is determined by the water valve The. water valve is factory set to maintain a high pressure. Low Side Pressure of 235 PSI 1 620 kPa To adjust the high pressure. Low side pressure expansion valve setting place the gauge on the high side access port Turn. the adjustment knob on the water valve clockwise to. To adjust the low side pressure place the gauge on lower the high side pressure and counterclockwise. the low side suction port at the compressor With the to raise the pressure. compressor running turn the adjustment knob of the. automatic expansion valve clockwise to raise the low The high side pressure switch is factory set at 440. side pressure and counterclockwise to lower the PSI 3 034kPa for 404A HP62 In the event of a. pressure water loss this switch will sense a rise in pressure. and deactivate the unit,High Side Pressure, Air Cooled The following chart indicates normal EPR Valve Setting. operating head pressures at various ambient, temperatures The product temperature in the mix hopper is.
maintained by the main refrigeration system and can. be adjusted by the EPR evaporator pressure, regulator valve The EPR valve is factory set at 67. 69 PSI 462 476 kPa in order to maintain hopper, Ambient Temperature Normal Operating Head product temperature below 40 F 4 C To adjust. the hopper temperature place the gauge on the, access port at the inlet of the EPR valve With the. F C PSI compressor running loosen the locking nut and turn. the adjustment screw located on the top of the, 70 21 1 240 270 valve clockwise to raise hopper temperature and. 1 655 1 862 kPa,counterclockwise to lower the temperature When.
80 26 7 270 300 the adjustment is complete tighten the locking nut. 1 862 2 069 kPa,90 32 2 300 340,2 069 2 344 kPa,100 37 8 340 380. 2 344 2 620 kPa,Introduction 6 Models 358 359,General Installation Instructions. CAUTION Only trained authorized service, technicians should install this equipment Failure to. comply will void the factory warranty This unit must be installed on a level. surface to avoid the hazard of tipping Extreme care. The following are general installation instructions should be taken in moving this equipment for any. For complete installation details please see the reason. checkout card, Two or more people are required to safely move this. unit Failure to comply may result in personal injury. or equipment damage, ALL WIRING AND PLUMBING MUST Uncrate the machine Inspect the unit for damage.
CONFORM TO NATIONAL AND LOCAL CODES Report any damage to the Taylor factory. immediately, INSTALL POTABLE WATER CONNECTION This piece of equipment is made in the USA and has. WITH ADEQUATE BACK FLOW USA sizes of hardware All metric conversions are. PROTECTION TO COMPLY WITH approximate and vary in size. APPLICABLE NATIONAL STATE AND,LOCAL CODES,Installer Safety. Site Preparation In all areas of the world equipment should. be installed in accordance with existing local codes. Review the area the unit is to be installed in before Please contact your local authorities if you have any. uncrating the unit Make sure that all possible questions. hazards to the user and the equipment have been, addressed Care should be taken to ensure that all basic safety. practices are followed during the installation and. servicing activities related to the installation and. service of Taylor equipment, Clearance Air Cooled Units S Only authorized Taylor service personnel. should perform installation and repairs on,Air cooled units require a minimum of 3 76 mm of.
the equipment,clearance around all sides of the unit Failure to. allow for adequate clearance can reduce the S Authorized service personnel should consult. refrigeration capacity of the unit and possibly cause OSHA Standard 29CFRI910 147 or the. damage to the compressor applicable code of the local area for the. industry standards on lockout tagout, For Indoor Use Only This unit is designed to procedures before beginning any installation. operate indoors under normal ambient or repairs, temperatures of 70 75 F 21 24 C The S Authorized service personnel must ensure. machine has successfully performed in high ambient that the proper PPE Personal Protective. temperatures of 104 40 C at reduced capacities Equipment is available and worn when. required during installation and service,S Authorized service personnel must remove. This unit must NOT be installed in an area all metal jewelry rings and watches before. where a water jet or hose can be used NEVER use working on electrical equipment. a water jet or hose to rinse or clean this unit Using a. water jet or hose on or around this equipment may, result in the electrocution of the user or damage to THIS UNIT HAS MANY SHARP EDGES.
the equipment THAT CAN CAUSE SEVERE INJURIES,Models 358 359 7 Introduction. Electrical Connections,Note This unit is provided with an equipotential. grounding lug that is to be properly attached to, either the rear of the frame or the under side of the. In the United States this equipment is, base pan near the entry hole for incoming power by. intended to be installed in accordance with the, the authorized installer The installation location is.
National Electrical Code NEC ANSI NFPA,marked by the equipotential bonding symbol 5021. 70 1987 The purpose of the NEC code is the,of IEC 60417 1 on both the removable panel and. practical safeguarding of persons and property from. the equipment s frame as well as on the diagram, hazards arising from the use of electricity This code. contains provisions considered necessary for safety. In all other areas of the world equipment should be. installed in accordance with the existing local codes. Please contact your local authorities S DO NOT operate the machine with larger. fuses than specified on the data label, Each machine requires one power supply Check S Stationary appliances which are not. the data label on the machine for fuse circuit equipped with a power cord and a plug or. ampacity and other electrical specifications Refer to another device to disconnect the appliance. the wiring diagram provided inside the control box from the power source must have an all pole. for proper power connections disconnecting device with a contact gap of. at least 3 mm installed in the external, It is recommended that the machine be plugged into installation.
an electrical surge protector for added protection S Appliances that are permanently connected. against power surges which could damage an,to fixed wiring and for which leakage. electrical electronics component An electrical surge. currents may exceed 10 mA particularly, event may cause the unit to shut down Such an when disconnected not used for long. event would require service by a qualified service. periods or during initial installation shall, technician if the machine was not adequately have protective devices such as a GFI to. protected A good surge protector as would,protect against the leakage of current and. normally be used on a home computer should be be installed by authorized personnel to the. adequate They are available at most computer retail. local codes,outlets or electrical supply stores,S Supply cords used with this unit shall be.
oil resistant sheathed flexible cable not,lighter than ordinary polychloroprene or. FOLLOW YOUR LOCAL ELECTRICAL CODES,other equivalent synthetic. elastomer sheathed cord Code designation,60245 IEC 57 installed with the proper cord. anchorage to relieve conductors from strain,including twisting at the terminals and. protect the insulation of the conductors from,CAUTION THIS EQUIPMENT MUST BE.
PROPERLY GROUNDED FAILURE TO DO SO, CAN RESULT IN SEVERE PERSONAL INJURY Failure to follow these instructions may result in. FROM ELECTRICAL SHOCK electrocution or damage to the machine. Introduction 8 Models 358 359,Refrigerant,Compressor Warranty Disclaimer. In consideration of our environment Taylor proudly The refrigeration compressor s on this machine are. uses only earth friendly HFC refrigerants The HFC warranted for the term indicated on the warranty. refrigerant used in this unit is R404A This card accompanying this machine However due to. refrigerant is generally considered non toxic and the Montreal Protocol and the U S Clean Air Act. non flammable with an Ozone Depleting Potential Amendments of 1990 many new refrigerants are. ODP of zero 0 being tested and developed thus seeking their way. into the service industry Some of these new, However any gas under pressure is potentially refrigerants are being advertised as drop in. hazardous and must be handled with caution replacements for numerous applications It should. NEVER fill any refrigerant cylinder completely with be noted that in the event of ordinary service to this. liquid Filling the cylinder to approximately 80 will machine s refrigeration system only the refrigerant. allow for normal expansion specified on the affixed data label should be used. The unauthorized use of alternate refrigerants will. void your compressor warranty It will be the owners. responsibility to make this fact known to any, Refrigerant liquid sprayed onto the skin may technicians they employ. cause serious damage to tissue Keep eyes and skin, protected If refrigerant burns should occur flush It should be noted that Taylor does not warrant the.
immediately with cold water If burns are severe refrigerant used in its equipment For example if the. apply ice packs and contact a physician refrigerant is lost during the course of ordinary. immediately service to this machine Taylor has no obligation to. either supply or provide its replacement either at. billable or unbillable terms Taylor does have the,obligation to recommend a suitable replacement if. Taylor reminds technicians to be cautious of, the original refrigerant is banned obsoleted or no. government laws regarding refrigerant recovery, longer available during the five year warranty of the. recycling and reclaiming systems If you have any,compressor. questions regarding these laws please contact the,factory Service Department.
Taylor will continue to monitor the industry and test. new alternate refrigerants as they are being,developed Should a new alternate prove through. WARNING R404A refrigerant used in our testing that it would be accepted as a drop in. conjunction with polyolester oils is extremely replacement then the above disclaimer would. moisture absorbent When opening a refrigeration become null and void To find out the current status. system the maximum time the system is open must of an alternate refrigerant as it relates to your. not exceed 15 minutes Cap all open tubing to compressor call the local Taylor Distributor or the. prevent humid air or water from being absorbed by Taylor Factory Be prepared to provide the. the oil model serial number of the unit in question. Models 358 359 9 Introduction,Environmental Notices. The user is responsible for returning the product to. the appropriate collection facility as specified by. In consideration of our environment Taylor proudly your local code. uses only earth friendly HFC refrigerants The HFC, refrigerant used in this unit is R404A This For additional information regarding applicable local. refrigerant is generally considered non toxic and laws please contact the municipal facility and or. non flammable with an Ozone Depleting Potential local distributor. ODP of zero 0 NOISE LEVEL Airborne noise emission does not. However any gas under pressure is potentially exceed 78 dB A when measured at a distance of. hazardous and must be handled with caution 1 0 meter from the surface of the machine and at a. height of 1 6 meters from the floor,If the crossed out wheeled bin symbol is. affixed to this product it signifies that this product is. compliant with the EU Directive as well as other, similar legislation in effect after August 13 2005.
Therefore it must be collected separately after its. use is completed and cannot be disposed as,unsorted municipal waste. Introduction 10 Models 358 359,Section 2 Controls Systems. S Thermistor Control,S Thermistor Curve,S Refrigeration System. S Maintaining Quality,Models 358 359 11 Controls Systems.


Related Books

KM-250B F Service Manual - Parts Town

KM 250B F Service Manual Parts Town

1 hoshizaki crescent cuber model service manual km-250baf km-250bwf no.: issued: revised: july 24, 2000 73094 december 22, 2004

990-T - liatis.com

990 T liatis com

Form 990-T Exempt Organization Business Income Tax Returned proxy tax under section 6033(e)) For calendar year 2009 or other tax year beginning , 2009, and

DOCUMENT RESUME HE 029 832 Guidelines for Filing IRS Forms ...

DOCUMENT RESUME HE 029 832 Guidelines for Filing IRS Forms

DOCUMENT RESUME ED 402 889 HE 029 832 TITLE Guidelines for Filing IRS Forms 990 and 990-T. INSTITUTION National Association of Coll. and Univ. Business

TWGHs Lee Ching Dea Memorial College Letter to Parents ...

TWGHs Lee Ching Dea Memorial College Letter to Parents

TWGHs Lee Ching Dea Memorial College Letter to Parents January 2019 7 January 2019 Dear Parents, This is to inform you of the recent school news, the arrangements of school administration affairs and school activities in January 2019. 1. Other reminders and important dates 2. Documents to be signed by parents Content Appendix Department Subject/Group Letter to Parents in January 2019 1 / The ...

990-T - MGWA

990 T MGWA

Form 990-T Department of the Treasury Internal Revenue Service Exempt Organization Business Income Tax Return (and proxy tax under section 6033(e))

MERANCANG PERHITUNGAN PADA SISTEM APLIKASI PERENCANAAN ...

MERANCANG PERHITUNGAN PADA SISTEM APLIKASI PERENCANAAN

dengan tenaga kerja, persediaan, tingkat produksi, dan kebutuhan kapasitas, yang kemudian diseimbangkan untuk mencapai tingkat produksi yang diharapkan dan memenuhi permintaan konsumen. Aktifitas produksi yang dibagi menjadi periode waktu yang lebih kecil untuk menentukan rencana produksi unit yang lebih spesifik disebut

PERANCANGAN BUDAYA KERJA 5S (Seiri, Seiton, Seiso ...

PERANCANGAN BUDAYA KERJA 5S Seiri Seiton Seiso

for the raw material warehouse at PT. Bonli Cipta Sejahtera based on 5S concept. So that the application of 5S concept can provide maximum results, a participatory ergonomics approach is applied so that all stakeholders within the warehouse are involved in improving the work area by conducting a FGD. The results from this research with the participatory ergonomics approach, showed that the ...

Physical & Interfacial Electrochemistry 2013

Physical amp Interfacial Electrochemistry 2013

Physical & Interfacial Electrochemistry 2013 Lecture 2. Electrolyte Solutions : Ion/solvent interactions: ionic solvation. Module JS CH3304 MolecularThermodynamics and Kinetics Ionics: the physical chemistry of ionic solutions. In previous lecture courses at the Freshman level we presented a rather general introduction to electrochemical systems and concepts. In this lecture course we begin ..

2016 Instructions for Form 990-T

2016 Instructions for Form 990 T

Form 990-T that was filed with the IRS, including all schedules and attachments. It also includes any amendments to the original return (amended return).

990-T Exempt Organization Business Income Tax Return

990 T Exempt Organization Business Income Tax Return

Form 990-T Department of the Treasury Internal Revenue Service Exempt Organization Business Income Tax Return (and proxy tax under section 6033(e))