Error Messages Garland Group-Books Download

ERROR MESSAGES Garland Group
06 Mar 2020 | 41 views | 0 downloads | 18 Pages | 1.38 MB

Share Pdf : Error Messages Garland Group

Download and Preview : Error Messages Garland Group


Report CopyRight/DMCA Form For : Error Messages Garland Group



Transcription

COMM ERROR, NO COMMUNICATION BETWEEN THE CONTROL BOARD AND THE MOTOR SPEED CONTROL. The comm error occurs when there is no communication between the. controller broard and the motor board,There is an audio alarm with the error message. The display should show COMM ERROR message in the first line. This error is not self healing error, To reset the error message and silence the beep press the ON OFF key. COMM ERROR, NO COMMUNICATION BETWEEN THE CONTROL BOARD AND THE MOTOR SPEED CONTROL. 1 Check the 5amp fuse Fig 1 2 If the fuse is blown you we need to. replace If the fuse is ok proceed to the next step. 2 Check for incoming power to the Motor board Fig 1 3 Depending. on what zone you are checking The wire Numbers are 1A 1B or 1C. and 2A 2B or 2C We should have 120 Volts AC If ok proceed to. the next step, 3 Check the 12 pin wire connections between Fig 1 1 and Fig 1 3.
The controls communicate through digital inputs and outputs make. sure all connections are secured Replace repair Harness as. IGNITION ERROR,after the 4th failed attempt to ignite. The gas ignition error occurs if the ignition feedback signal does not. give the proper signal after 4 tries default 30 seconds on time and 7. seconds off time, The display should show IGNITION ERROR message in the first. There is an audio alarm with the error message,This error is not self healing error. To cancel the error message press the ON OFF key,MOTOR ERROR2. The motor error 2 is seen when the grill platen hasn t reached its expected. position in 30 seconds 30 seconds corresponds to 150 good packets. received from the motor control board 1 packet every 200 msec. The error message will flash and there will be an audio alarm. To cancel the error message the power switch must be recycled. The display will show MOTOR message in the first line and the. ERROR2 message in the second line,UPPER SWITCH ERROR.
This error appears in code but is never set, The error message will flash and there will be an audio alarm. To cancel the error message the power switch must be recycled. The display will show UPPER SWITCH message in the first line. and the ERROR message in the second line,LOWER SWITCH ERROR. This error is seen when the platen is going down and doesn t reach. the lower limit switch within 200 plus calibrated steps Note. calibration steps default 1300, The error message will flash and there will be an audio alarm. To cancel the error message the power switch must be recycled. The display will show LOWER SWITCH message in the first line. and the ERROR message in the second line,PLATEN DOWN ERROR. IF PLATEN DOES NOT REACH THE PROPER POSITION IN 40 SECONDS. The platen down error occurs if the platen does not reach the proper position in 40. seconds or fails to move during this time,There is an audio alarm with the error message.
The display should show PLATEN DOWN message in the first line and ERROR. message in second line,This error is not self healing error. To cancel the error message press the ON OFF key,PLATEN UP ERROR. PLATEN IS BELOW THE LOWER LIMIT SWITCH AND DOES NOT MOVE FOR 40 SECONDS. The platen up error occurs if the platen is below the limit and does not. move for 40 seconds,There is an audio alarm with the error message. The display should show PLATEN UP ERROR message in the first. This error is not self healing error,To cancel the error message press the ON OFF key. MOTOR ERROR,NO ENCODER MESSAGE TO THE MOTOR SPEED CONTROL.
The motor error occurs when the platen is going up or down and does not. get 5 encoder counts in 1 second when the platen is below the lower limit. moving down or above the lower limit going up, The error message will flash and there will be an audio alarm. To cancel the error message the power switch must be recycled. The display will show MOTOR message in the first line and the. ERROR message in the second line,MOTOR OVERCURRENT. THE PLATEN HAS BEEN MECHANICALLY RESISTED,Mount to Cross Member. OR Manually spinning actuator shaft,may free gears if binded. The motor over current error is displayed when the platen Input leads Gears. has been mechanically resisted 75 VDC 140 VDC, The motor over current error occurs when the circuit detects Encoder.
a fault when a current to the motor is greater than 4 8 AMPs. the current could be as high as 13 AMPs, The motor current is 0 7 AMPs to start and 0 5 AMPs. running on the test fixture in normal condition, The platen will stop and move to the lower limit switch Mount for actuator base. The display should show MOTOR message in the first line. and the OVERCURRENT message in the second line,This error is not self healing error. Press RAISE button to eliminate this display,HEATING ERROR. CONTROLLER IS NOT DETECTING A PROPER TEMPERATURE RESPONSE OVER A SIX MINUTE. The heating error occurs when the controller doest not detect a proper. temperature response over a six minutes period, The corresponding tri color LED will turn red indicating which element is in.
The display should show HEATER ERROR message in the first line if it is. the grill heater error and the grill heater bottom LED will turn and flash red. There is an audio alarm with the error message, The display should show HEATER ERROR message in the second line if it is. the platen heater error and the platen heater top LED will turn red There is no. an audio alarm with the error message, The display should show HEATER ERROR message in the first line if it is. the grill and platen heater errors and both LEDs will turn and flash red There is. an audio alarm with the error message,This error is not self healing error. To cancel the error message press the ON OFF key,HEATING ERROR. CONTROLLER IS NOT DETECTING A PROPER TEMPERATURE RESPONSE OVER A SIX MINUTE. Fig 2 2 Fig 2 5 A,Fig 2 5 B1,Fig 2 5 B2,HEATING ERROR.
CONTROLLER IS NOT DETECTING A PROPER TEMPERATURE RESPONSE OVER A SIX MINUTE. Note If your griddle uses gas for its energy you will most likely get an ignition error first If you do not get the Ignition. Error first either a component has failed or a miss wiring has occurred Go to the information page and check Wiring. Diagram and or check Ignition Error Page, 1 Determine which heating surface is causing Error By viewing the LED Light and finding the corresponding Red light. Now proceed to the next step, 2 Confirm the breakers are on Fig 2 1 This would bring power to the contactor Proceed to the next step. 3 Using caution check for power to The contactor Fig 2 2 Check for power out of contactor No power out check for. voltage on the coil if power is present replace contactor If power is not present check the Hi Limit in the platen Fig 2. 3 Replace as needed or continue to the next step, 4 We have power out of the contactor now check the Solid State Relay s out put to the elements no power out confirm. that the control has sent the dc voltage to terminals 3 4 if the SSR has a led light it should be illuminated during a. call for heat Fig 2 4 Replace as needed or continue to the next step. 5 Have power out of Solid State Relay check the elements Fig 2 5 A Platen 2 5 B1 and 2 5 B2 grill Replace as. PROBE ERROR,PROBE IS OPEN OR NOT CONNECTED, The probe error occurs when the probe is open or not connected The controller will turn the heat off. If the fault is in the platen probe the grill can still be used if product recipes are flat recipes. If the grill probe is opened the grill will not operate. The corresponding tri color LED will turn red indicating which element is in error. The display should show PROBE ERROR message in the first line if it is the grill probe error and the grill. heater bottom LED will turn and flash red There is an audio alarm with the error message. The display should show PROBE ERROR message in the second line if it is the platen probe error and the. platen heater top LED will turn red There is no an audio alarm with the error message. The display should show PROBE ERROR message in the first line if it is the platen and grill probe errors and. both LEDs will turn and flash red There is an audio alarm with the error message. This error is not self healing error,To cancel the error message press the ON OFF key.

Related Books

Mika, E. (2017). Who goes trump? Tyranny as a triumph of ...

Mika E 2017 Who goes trump Tyranny as a triumph of

All tyrants share several essential features: they are predominantly men with a specific character defect, narcissistic psychopathy (a.k.a. malignant narcissism). This defect manifests in a severely impaired or absent conscience and an insatiable drive for power and adulation that masks the conscience deficits. It forms the core of attraction between him and his followers, the essence of what ...

KEPIMPINAN TEKNOLOGI PENGETUA DAN HUBUNGANNYA DENGAN ...

KEPIMPINAN TEKNOLOGI PENGETUA DAN HUBUNGANNYA DENGAN

1 Lembaga Peperiksaan Kementerian Pendidikan Malaysia 2 Universiti Kebangsaan Malaysia Accepted date: 29 July ... I. M. (2017). Kepimpinan Teknologi Pengetua Dan Hubungannya Dengan Prestasi Akademik Sekolah Di Malaysia. International Journal of Education, Psychology and Counseling, 2(5), 215-230. ABSTRAK: Pengetua sebagai pemimpin teknologi di sekolah menghadapi tugas yang mencabar dalam ...

Oracle WebLogic Server

Oracle WebLogic Server

Introduction to Oracle WebLogic Server 1-3 zJava Messaging Service (JMS) enables applications to communicate with one another through the exchange of messages. A message is a request, report, and/or event that contains information needed to coordinate communication between different applications.

Standard Wundbehandlung bei Erwachsenen

Standard Wundbehandlung bei Erwachsenen

Datei Autor Zur Genehmigung Ersetzt Version vom Freigabe Seite Standard Wundbehandlung bei Erwachsenen Siehe Seite 2 29.02.2012 28. Februar 2007 31. 05.2012 1/34

No. NF-T-1 - IAEA

No NF T 1 IAEA

Uranium Mining: An Overview of Operations No. NF-T-1.4. IAEA NUCLEAR ENERGY SERIES PUBLICATIONS STRUCTURE OF THE IAEA NUCLEAR ENERGY SERIES Under the terms of Articles III.A and VIII.C of its Statute, the IAEA is authorized to foster the exchange of scienti?c and technical information on the peaceful uses of atomic energy. The publications in the IAEANuclear Energy Series provide information ...

Exploring Uranium Resource Constraints on Fissile Material ...

Exploring Uranium Resource Constraints on Fissile Material

Exploring Uranium Resource Constraints on Fissile Material Production in Pakistan Zia Mian,1 A. H. Nayyar,2 and R. Rajaraman3 1Program on Science and Global Security, Woodrow Wilson School of Public and International Affairs, Princeton University, Princeton, NJ, USA 2Sustainable Development Policy Institute, Islamabad, Pakistan 3School of Physical Sciences, Jawaharlal Nehru University, New ...

What is a Complex Adaptive System? - Code.org

What is a Complex Adaptive System Code org

What is a Complex Adaptive System? PROJECT GUTS PAGE 2 What are Complex systems ? (a.k.a. Complex Dynamic Systems or Complex Adaptive systems) Complex = difficult-to-understand or difficult to predict Dynamic = moving, changing Adaptive = changing to adapt to an environment or condition Complex systems are collections of simple units or agents interacting in a system. A complex system is a ...

spring-security - RIP Tutorial

spring security RIP Tutorial

from: spring-security It is an unofficial and free spring-security ebook created for educational purposes. All the content is extracted from Stack Overflow Documentation, which is written by many hardworking individuals at Stack Overflow. It is neither affiliated with Stack Overflow nor official spring-security.

MSYRN Floor Plans - English

MSYRN Floor Plans English

1718 DESIGN CENTER ATRIUM ELEVATORS STAIRS TO THIRD HYATT REGENCY NEW ORLEANS 601 Loyola Avenue, New Orleans, Louisiana 70113 USA T: +1 504 561 1234 F: +1 504 523 0488 hrno.sales@hyatt.com neworleans.hyatt.com RESTROOMS 2 HALL 3-D FLOOR PLAN All Levels

Washington State Functional Family Therapy Project

Washington State Functional Family Therapy Project

Washington State Functional Family Therapy Project Quality Assurance and Quality Improvement System Approved by CJAA Committee July 25th 2014 Introduction The Washington State Functional Family Therapy project is dedicated to maintaining a high degree of model fidelity to the Functional Family Therapy (FFT) model. Evidence-based and research based intervention programs depend on high model ...